Audiovox stereo wiring diagram
AUDIOVOX CP-250
AUDIOVOX AV-220
Diagram wiring, wiring diagram, car radio wiring diagram.
Audi Car Stereo Wiring Diagram
AUDI GAMMA
 | A | B | C |
1-Gala | 1-Speaker RR+ (not all models) | 1-Data | |
2-Gnd | 2-Speaker RR- (not all models) | 2-Clk | |
3-Control+12V | 3-Speaker RF+ | 3-Ena | |
5-Power Antenna Turn On | 4-Speaker RF- | 5-Gnd | |
6-Dash Light Dimmer Wire | 5-Speaker LF+ | 6-Control+12V | |
7-+12 VOLT IGNITION WIRE | 6-Speaker LF- | 7-Line out RF | |
8-Gnd | 7-Speaker LR+ (not all models) | 8-Line out RR | |
- | 8-Speaker LR- (not all models) | 9-Line out LF | |
- | - | 10-Line out LR |
Alpine Car Stereo Wiring Diagram
ALPINE TDE-7823W
 | 1-+12 Volt Battery Wire | 9-Gnd |
2-Speaker LR- | 10-Speaker LF- | |
3-Speaker LR+ | 11-Speaker LF+ | |
4-Speaker RR- | 12-Speaker RF- | |
5-Speaker RR+ | 13-Speaker RF+ | |
7-Booster | 16-+12 VOLT IGNITION WIRE | |
8-Power Antenna Turn On | - |
ALPINE 7190M
 | 2-Booster | 28-Speaker LF+ |
8-Gnd- Line out | 29-Gnd | |
9-Line out R | 31-+12 Volt Battery Wire | |
10-Line out L | 32-+12 VOLT IGNITION WIRE | |
13-Power Antenna Turn On | 34-Speaker RR+ | |
26-Speaker LR+ | 35-Speaker RR- RF- | |
27-Speaker LR- LF- | 36-Speaker RF+ |
ISO Car Radio Connectors
|
| ISO
| B 1 Right Rear + |
| B 2 Right Rear - | ||
| B 3 Right Front + | ||
| B 4 Right Front - | ||
| B 5 Left Front + | ||
| B 6 Left Front - | ||
| B 7 Left Rear + | ||
| B 8 Left Rear - | ||
| ISO
| A 1 GALA Geschwindigkeitsabhängige Lautstärkeranpassung or SCV speed-dependent volume control. | |
| A 2 Mute from Cell-Phone | ||
| A 3 RFLS Ruckfahrtlichtschalter - the reversing light switch. | ||
| A 4 Memory Power (12V direct from Battery) | ||
| A 5 Power for Electric Antenna | ||
| A 6 Dial-light illumination (car side light circuit) | ||
| A 7 +12V Main Power (Switched via Ignition key) | ||
| A 8 Ground (Chassis) |
Attention:
The connector wiring may vary depending on the car manufacturer, even when ISO connectors are used. We recommend to check the car’s wiring provision before connecting the car stereo.
Please pay particular attention to pin 5, where a misconnection might cause damage to the car or radio.
Take special care when installing into ’98 or later VW/Audi/Skoda/Seat models as there may bea 12 V connection on Pin 5, which could damage the car stereo or into Ford from ’97 or later , with an ISO connector, on which damage to the car’s microcomputers is possible if misconnected.
Use of ISO connector adapters available on the market may facilitate installation.
ISO 10,487 is a standard 8-pin connector that is used in Autoradio device (head unit). There are contacts for the power cord, off / on (controlled ignition key), the speakers and automatic antenna.
| ISO Connector A napajanje |
| PIN 1 - GALA Geschwindigkeitsabhängige Lautstärkeranpassung - or SCV speed-dependent volume control. |
| PIN 2 - Mute control - this pin is used to mute the sound car, uzemljuje it out some other component such as a mobile phone that is connected to the car. |
| PIN 3 - RFLS Ruckfahrtlichtschalter - the Reversing light switch. Satellite navigation uses this signal, GALA signal (pin 1) and internal laser gyroscope to calculate in the absence of satellite signals. +12 V input on the car involved contact with the lock on the ignition and the car's speed to move backwards. |
| Pin 4 - +12 V with fixed batteries - power for Autoradio. Autoradija linking directly to the battery, it is not necessary to have the key in the ignition lock. Autoradio Some modern devices have an automatic exclusion. This connector connects the memory Autoradio. |
| PIN 5 - automatic antenna - exit from the car +12 V maximum 150 - 300mA power supply automatic or electronic antennas. If there has to be connected, although not automatic antenna. He also manages a sound signal, which warns that the door is open. |
| PIN 6 - light +12 V input on autoradiju when the lights turned on. In some car really shines on display - the other can be dark lighting, replace the relationship between black and white, or even changes color from green to orange. If the dashboard of the car has a brightness control function, this pin must be connected in order to be able to regulate the brightness. Wire lighting the cigarette lighter can be used for. |
| PIN 7 - +12 V with the ignition key when the key in the lock to ON or ACC position. |
| PIN 8 - uzemljenje, chassis, minus 12V |
| ISO Konektor B - zvučnici |
|
· Pin 1 - Right rear speaker + zadnji desni zvučnik + · Pin 2 - Right rear speaker - zadnji desni zvučnik - · Pin 3 - Right front speaker + prednji desni zvučnik + · Pin 4 - Right front speaker - prednji desni zvučnik - · Pin 5 - Left front speaker + lijevi prednji zvučnik + · Pin 6 - Left front speaker - lijevi prednji zvučnik - · Pin 7 - Left rear speaker + lijevi zadnji zvučnik + · Pin 8 - Left rear speaker - lijevi zadnji zvučnik -
|
| B connector is used only for the speakers. Which wire goes to which speaker can be easily determined with a battery of 1.5 V. Speaker will click and you will move forward or backward membrane. Speakers must be properly fazirani (note the + and - half to the speaker), because otherwise you will have weak bass. Speaker wires are in pairs, with a stripe wire is the + pole speakers. |
| C1 - external amplifier or equaliser |
|
|
| C2 - remote control |
|
|
| C3 - CD changer |
|
|
| ISO connector C |
| Connector C are actually three separate connectors that are užlijebljena together. It is not always present, sometimes only a part. It is usually connected to the device which supports. |
Decoding Blaupunkt RCC24 RCC44 radio WITH TMS375 and Toshiba PROCESSOR
Rerather challenging for the tms375
Linking RCC at 24
Blaupunkt series radios RCC24,RCC44 and RCR84 contentže processor Toshiba TMP47C660F whichand is soldered with Solder the printed circuit board and processor Texas Instruments TMS375C006 that was soldered with top of the printed Plates. The code is written in TMS375 but the reading is done in code TMP47C660. Each time involved fPlanning radio mpdid you transfer data from the TMP47C TMS375 processor in which is a code that we are interested. Reading this information to work with Motorola's interface and Term95.exe program contained within the Norton Commander's. In Read our data will be visible only if the radio allows entry codes. If radio does not allow entry codes allow it involved 60 minutes. With motorolinog interface associate processor to extract RXD the interface to TXD TMP47C of processors. At Radio Blaupunkt Dusseldorf RCR84 pin from the processor on which the excerpt is associate RXD 51 pin and is located on the corner of the processor.In read the data code is in the last two bytes.
For example: 61 92 54 CO CO CO 60 94 61 02 05
When the 0205th
Adjustingvidual settings Term95.exe
1 degrees
When you start Norton Commander if the upper part window is not visible to me, press F9, and appears to me to options: Left Files Disk Commands Right
Click option Commands and choose Terminal emulation. This onfYou start in program Term95.exe which will open over the previous window.
Adjustingvidual settings Term95.exe
2 levels
Click Settings and the Driver and check the Standard if it has not so elected.
Adjustingvidual settings Term95.exe
3 degree
Click Settings and the Line open and you are set as in Figure levo.Podesite all same as shown in figure if you connected to the interface COM1.Promenu with one option to another carry with Tab and select the up and down arrows on the end tastaturi.Na confirm with OK.
Adjustingvidual settings Term95.exe
4 degrees
Click Settings and the Terminal emulation and check the HEX.
Adjustingvidual settings Term95.exe
5 degrees
Click Connect and then AutoAnswer. In this last setting you activate the program that scans the developments in the COM1 serial port and displays the data in hexadecimal format on the screen.
Briefly the decoding of the radio is as follows:
# IncreaseGND inhabitants interfaces to the mass of the radio interface and RXD to 51 Toshiba processor pin (pin on the corner)
# Motorola interface does not compromise power supply (some models required)
# Connect all required power radio
# Start Term95 program that you previously set the pictures above
# Include radio (if radio shows in the display code into read data, you will be visible code)
DECODE RADIO WITH TMS375 and Toshiba PROCESSOR
Blaupunkt Car Radio Wiring DiagramAuto radio wire connection . |
BLAUPUNKT CCP08, Denver SQR88, Sylt SQR88
|
BLAUPUNKT Alpha CC
| |||||||||||||||||||||||||||||||||||||||||||||||||
BLAUPUNKT RDM & RCM 126, 127, 128 ; Fun Line (not all)
| |||||||||||||||||||||||||||||||||||||||||||||||||
BLAUPUNKT Fun Line 2 : Cassablanca CD50, ... 
| |||||||||||||||||||||||||||||||||||||||||||||||||
BLAUPUNKT
| |||||||||||||||||||||||||||||||||||||||||||||||||
BLAUPUNKT RDM & RCM 126, 127, 128 ; Fun Line (not all)
 | A | B | C | |
2-Tel mute | 1-Speaker RR+ | 1-Line out LR | 12-Remote control | |
4-Control | 2-Speaker RR- | 2-Line out RR | 13-Scl | |
5-Power Antenna Turn On | 3-Speaker RF+ | 3-Gnd- Line out | 14-Sda | |
6-Dash Light Dimmer Wire | 4-Speaker RF- | 4-Line out LF | 16-Control12V | |
7-+12 VOLT IGNITION WIRE | 5-Speaker LF+ | 5-Line out RF | 17-Gnd | |
8-Gnd | 6-Speaker LF- | 6-12V | 18-Gnd- Input | |
- | 7-Speaker LR+ | 10-Remote control | 19-Input L | |
- | 8-Speaker LR- | 11-Remote control | 20-Input R | |
- | - | - | 13-20-CD Changer Interface | |
BLAUPUNKT Lubeck SQM 28
 | 1-Power Antenna Turn On |
2-Control | |
3-+12 VOLT BATTERY WIRE | |
4-GND | |
5-Speaker R | |
6-Speaker L |
BLAUPUNKT San Francisco SQR28
 | 1-Booster/antenna | 9-Speaker LF- |
2-Line out | 10-Speaker RF- RR- | |
3-Line out | 11-Speaker LF+ LR+ | |
4-Line out | 13-Speaker RR+ | |
5-Line out | 14-Speaker LR- | |
6-GND Line out | 15-+12 VOLT IGNITION WIRE | |
7-Dash Light Dimmer Wire | 16-+12 VOLT BATTERY WIRE | |
8-Speaker RF+ | 17-GND |
Subscribe to:
Posts (Atom)