Philips car 400 code

Your CAR400 stereo will be locked any time the battery is disconnected from the car. This is a Vauxhalls vehicles antitheft security system to prevent unauthorized use of your car radio cassette.

If you are looking for philips car400 code, it is possible to generate it within seconds from the EEPROM Dump file using one of the radio code calculators available for download. After getting your code you'll need to enter it using the numeric keypad in order to use the stereo again. But first of all you should verify if your 4 digit number code is written somewhere in your paper, this will save you a lot of time. If you are sure you don’t have the unlock code, I will show you how to reset car400 radio code with DUMP code generator.

Philips Vauxhalls car stereo removal

To remove the Radio, you may need to remove four small Allen Key screws in the front panel before the removal tools (PC5-83) can be inserted through the holes. Once the removal tools are inserted, push in until a click is felt, and then withdraw the radio. The cage and leads will probably remain fixed to the car.

How to program a vauxhall vehicle display problem?

There are two versions of Vauxhall vehicle displays, one with 8 Digits and one with 10 Digits. If you connect this stereo to the wrong display, code entry is possible, but the display will either freeze or disappear. Turn off Radio, Press and Hold Presets "4" & "6" at the same time to toggle between the two display modes.

Download Philips car 400 code calculator

These car radio code generators are able to calculate Philis car 400 stereo codes from an EEPROM DUMP file. So you must have an eeprom programmer to be able to read the information in the 24C16 circuit. Once you have Dump file, put it in the code generator software and hit calculate, your code will be generated instantly.

• PHILIPS code reader Ccr600 CAR400 MK1
• Philips Code Reader From Dump gammaIV car400
• vauxhall Code calculator CAR400 600 GAMMA
• Philips Car600 Car400 MK1 decoder from EEPROM
• Car Radio eeprom code generator Philips Ford Grandig
• Vauxhall Philips Car400 radiodecoder

Vauxhall car 400 code entry instructions

To enter your car 400 stereo code, it is very simple, just follow the following steps in the correct order:
In the beginning turn Off the radio then switch On the ignition without starting the engine.
Now press & Hold Preset the " AS " button and switch stereo On. At this point the display will show "SAFE", then you will see "10 - - - -". The next step is to enter the 4 digits car 400 code digit after digit:

• Press preset [ 1 ] repeatedly for the first digit
• Press preset [ 2 ] repeatedly for the second digit
• Press preset [ 3 ] repeatedly for the third digit
• Press preset [ 4 ] repeatedly for the last digit

Finally, to save the code press & hold "AS" button until the radio unit beeps.
Please note that if the display shows a number less than 10, and the word SAFE, then the unit may be code-locked. So, you must leave it switched on for up to two hours and a further attempt at code entry should be possible. If not, the unit must be sent to professional radio decoding service to reset car400 stereo.

PHILIPS CAR400 MK1 (DC396/75E) GM0400 no display CODE 0000-9999 90 532 621 (panel GM90506173 1614438) PHILIPS P83CE559EFB030 (RC3-DC396/075) 24C16 EEPROM TDA7372A

PHILIPS CAR400 MK2 (DC399/75) GM0400 no display CODE 0000-9999 24 455 379 (panel GM90506173 1614438) PHILIPS P83CE560EFB054 24C16 smd EEPROM TDA7375

Vauxhall CAR 400 MK3 SIEMENS VDO CAR400 DC399 GM0400 no display CODE 0000-9999 09 119 904 SIEMENS VDO P83CE560EF061 24C16 smd EEPROM TDA7375 x 2

Related posts about philips CAR400 decoding:

• Vauxhall stereo removal guide
• Vauxhall VDO CDR 2005 Code Entry Instructions
• Code calculator for Renault radios Philips,VDO,Pioneer from PreCode